Penerapan metode Hirarc K3 mesin gerinda tangan pada industri fabrikasi PT. XYZ

Authors

  • Manggi Dwi Cahyono Universitas 45 Surabaya
  • Lalak Indiyono Universitas 45 Surabaya
  • M Yusuf Arnold Universitas 45 Surabaya
  • Devi Susiati Universitas 45 Surabaya

DOI:

https://doi.org/10.31004/jutin.v8i1.40700

Keywords:

Hirarc, K3, Gerinda, Industri, Fabrikasi

Abstract

XYZ is one of the industries engaged in the fabrication sector. The workplace is not too large, making the production area full of machines and piles of equipment so that it can cause danger to workers and the company. This study aims to ensure that all workers at PT. XYZ know the procedures for using hand grinders properly and correctly, and comply with all regulations when using work tools. This study uses the HIRARC method to identify the problems experienced. Based on the results of the analysis of the study referring to the occupational safety and health (K3) of hand grinders in the fabrication industry at PT. XYZ shows that there are still many activities that can pose dangerous risks. The solution is to redesign K3 management at PT. XYZ by conducting socialization of the dangers of work accidents and conducting direct and continuous supervision of workers about the importance of using personal protective equipment. So that in the future it is expected to increase productivity in the fabrication industry at PT. XYZ.

References

Andi Asnur Pranata M. H, Uppit Yuliani, & Ellysa Ellysa. (2024). Analisis Pelaksanaan Dan Perhitungan Kebutuhan Beton Pekerjaan Kolom Pada Proyek X Cibubur. Jurnal Ilmiah Teknik, 3(2), 82–91. https://doi.org/10.56127/juit.v3i2.1434

Angrayni, S. A., & Audina, N. (2023). IDENTIFIKASI BAHAYA dan PENILAIAN RISIKO KECELAKAAN KERJA pada BENGKEL LAS MENGGUNAKAN PENDEKATAN JOB SAFETY ANALYSIS. Inovtek Polbeng, 13(1), 105. https://doi.org/10.35314/ip.v13i1.3328

Imam Pratomo, F., Hendrajaya, A., Alfarisy Ferysyah, E., & Nuriskasari, I. (2022). Proses Manufaktur dan Analisa Jig Sliding Cutting pada Permesinan Gerinda Tangan. Prosiding Seminar Nasional Teknik Mesin Politeknik Negeri Jakarta, 1546–1553. http://prosiding.pnj.ac.id

Mahmud, Zulfadli, Hilmi, Dirhamsyah Muhammad, & Azwar. (2022). Pelatihan K3 Kepada Juru Las Pada Usaha Bengkel Las CV. Alfazil Jaya. Communio: Jurnal Pengabdian Kepada Masyarakat, 1(2), 89–94.

Muktar, R., & Pratoto, A. (2023). Reduction of specific energy consumption (SEC) in cement factories through FMEA and energy management. Teknika: Jurnal Sains Dan Teknologi, 19(1), 43. https://doi.org/10.36055/tjst.v19i1.20225

Nurman, M., & Harto, D. (2024). Rancang Bangun Alat Pengukur Paparan Getaran Mesin Gerinda Yang Berpengaruh Terhadap Havs Berbasis Arduino. Jurnal: Elektrika Borneo (JEB), 10(1), 8–13.

Permana, A., & Nugroho, A. J. (2022). Job Safety Analysis (Jsa) Pada Area Workshop Pt Widya Inovasi Indonesia. Jurmal Ilmiah Teknik Mesin, Elektro Dan Komputer, 2(1), 63–73.

Pratama Rahman, M. D., Priyana, E. D., & Rizqi, A. W. (2022). Job Safety Analysis (JSA) Sebagai Upaya Pengendalian Resiko Kecelakaan Kerja Pada Pekerjaan Fabrication Dd PT. Wilmar Nabati Indonesia. Teknika Sains: Jurnal Ilmu Teknik, 7(2), 98–109. https://doi.org/10.24967/teksis.v7i2.1947

Putra, M. D. D., Widada, D., & Fathimahhayati, L. D. (2022). Analisis Keselamatan dan Kesehatan Kerja dengan Menggunakan Metode Hazop pada Bengkel Tejo Steel. Journal of Industrial and Manufacture Engineering, 6(2), 144–152. https://doi.org/10.31289/jime.v6i2.7570

Ririh, K. R., Fajrin, M. J. D., & Ningtyas, D. R. (2020). Analisis Risiko Kecelakaan Kerja Dengan Menggunakan Metode HIRARC dan Diagram FISHBONE Pada Divisi Warehouse di PT. Bhineka Ciria Artana. Semrestek 2020, 8–13. http://teknik.univpancasila.ac.id/semrestek/prosiding/index.php/12345/article/view/376

Sariman, F., & Cipto. (2023). Pelatihan Mengelas dengan Kelengkapan Keselamatan dan Kesehatan Kerja (K3). Kawanad : Jurnal Pengabdian Kepada Masyarakat, 2(1), 9–14. https://doi.org/10.56347/kjpkm.v2i1.92

Yuliyono, F. A., & Nuruddin, M. (2022). Identifikasi Risiko Kecelakaan Kerja Pada Bengkel Las Menggunakan Pendekatan Job Safety Analysis. RADIAL : Jurnal Peradaban Sains, Rekayasa Dan Teknologi, 10(1), 11–22. https://doi.org/10.37971/radial.v10i1.264

Downloads

Published

2025-01-17

How to Cite

Cahyono, M. D., Indiyono, L., Arnold, M. Y., & Susiati, D. (2025). Penerapan metode Hirarc K3 mesin gerinda tangan pada industri fabrikasi PT. XYZ. Jurnal Teknik Industri Terintegrasi (JUTIN), 8(1), 814–823. https://doi.org/10.31004/jutin.v8i1.40700

Issue

Section

Articles of Research

Similar Articles

1 2 3 > >> 

You may also start an advanced similarity search for this article.