Evaluasi Keandalan Mesin Gilingan Tebu dengan Menggunakan Metode Reliabelity Centered Maintenance (RCM) di PG. XYZ
DOI:
https://doi.org/10.31004/jutin.v8i3.46953Keywords:
Downtime, RCM, MTTF, MTTR, LTAAbstract
Industry in indonesia which is increasingly experiencing development encaurages PG.XYZ increases the realiabelity of the machine on the sugar cane milling machine, especially on the unigrator knife component, the method used in the sudy is the use the Realiabelity Centered Maintenance (RCM) methode. Data was taken during the 2023 and 2024 milling seasone, with risk analysis using FMEA Risk Priority Number the value obtained was 216 and a precentage of 17.%. Significant downtime of 1540 minutes (30%) was recorded due to the replacement of the componen. RCM analysis use the weibull distribution matrix bicause it most accurately describes the damge pattern, with an MTTF value of 588.57 hours, MTTR I hour 58 minutes. And MTBF of 225.8 hours. And for Condition derected maintenance actions, and these findings indicate the need for scheduling intervals to reduce further downtime so as to increase operational efficiency to optimally extend the life of the component.References
Akbar Waluyo, A., & Widyaningrum, D. (2023). Perbaikan Sistem Perawatan Mesin Forming dengan Metode FMECA dan RCM Berdasarkan Analisis OEE pada PT XYZ. Jurnal Serambi Engineering, 8(4), 7281–7290.
Fathurohman, F., & Triyono, S. (2020). Rcm (Reliability Centered Maintenance): the Implementation in Preventive Maintenance (Case Study in an Expedition Company). EKOMABIS: Jurnal Ekonomi Manajemen Bisnis, 1(02), 197–212.
Febryan, C., Luh, N., Lilis, P., Setiawati, S., Teknik, F., & Udayana, U. (2024). Jurnal Taguchi. 31–41.
Hidayat, H., Jufriyanto, M., & Rizqi, A. W. (2021). Perancangan RCM (Reliability Centered Maintenance) Untuk Mengurangi Downtime Mesin Pembuat Botol (Studi Kasus PT IGLAS (Persero), Gresik). Matrik, 21(2), 157.
Ishak, A., Sari, R. M., & Sabri, G. H. (2023). Perencanaan Sistem Pemeliharaan Mesin Screw Press Menggunakan Metode Reliability Centered Maintenance ( Studi Kasus pada PMKS ). Prosiding Seminar Nasional Teknik Industri (SENASTI) 2023, 324–334.
Muhazir, A., Sinaga, Z., & Septiadi, R. D. (2024). Perencanaan Perawatan Mesin Building Dengan Metode Reliability Centered Maintenance (RCM). Jurnal Optimalisasi, 10(1), 120.
Pattiapon, M. L. (2024). Industri Inovatif-Jurnal Teknik Industri ITN Malang, Maret 2024 Analisis Perawatan Mesin Cetak Paving Block | Pattiapon ANALISIS PERAWATAN MESIN CETAK PAVING BLOCK DI UD. X DENGAN PENDEKATAN RELIABILITY CENTERED MAINTENANCE DAN MAINTENANCE VALUE STREAM MA. 22–30.
Pramudia, N. S., & Fuadati, S. R. (2020). Pengaruh Pertumbuhan Perusahaan dan Ukuran Perusahaan Terhadap Nilai Perusahaan. Jurnal Ilmu Dan Riset Manajemen, 9(7), 2614–3259.
Putra, R., Arungpadang, T. A. R., & Neyland, J. S. C. (2024). Perawatan Sistem Pengisian Produk Menggunakan Metode Reliabelity Centered Maintenance dI PT.Pertamina Patra Niaga Itegrated Terminal Belitung. Ejournal.Unsrat.Ac.Id, 10(2), 129–140.
Simanungkalit, R. M., Suliawati, S., & Hernawati, T. (2023). Analisis Penerapan Sistem Perawatan dengan Menggunakan Metode Reliability Centered Maintenance (RCM) pada Cement Mill Type Tube Mill di PT Cemindo Gemilang Medan. Blend Sains Jurnal Teknik, 2(1), 72–83.
Theresia, L., Ranti, G., & Widianty, Y. (2023). Implementasi Lean Reliability Centered Maintenance (RCM) untuk Meningkatkan Keandalan Mesin: Studi Kasus PT Pelita Cengkareng Paper. Jurnal IPTEK, 7(2), 13–20.
Waskito, B., Abdillah, H., & Dwiyanto, A. (2025). Analisis Perawatan Mesin Belt Conveyor di PT . X. Journal Of Social Science Research, 5(1), 2969–2978.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Ahmad Hari Setiawan, Aan Zainal Muttaqin, Doni Susanto
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
