Sifat Ketangguhan Baja ST 42 Pasca Post Welding Heat Treatment dengan Media Pendingin Minyak Kelapa pada Variasi Holding Time
DOI:
https://doi.org/10.31004/jutin.v9i1.55185Keywords:
Heat treatment temperature, Holding time, Coconut oil cooler, Toughness, PWHT, ST 42 steelAbstract
Post-Weld Heat Treatment (PWHT) is applied in heat treatment processes, holding time, heating temperature, and cooling rate are very important factors. PWHT is also intended to relieve residual stresses (stress relieving). Therefore, this study aims to determine the effect of holding time with coconut oil as the cooling medium in PWHT on the toughness of ST 42 steel. The research method employed was an experimental method using a heat treatment temperature of 590°C, holding times of 1, 2, 3, 4, and 5 hours, and coconut oil as the cooling medium, after SMAW welding at a current of 120 A, using an E6013 electrode, flat welding position, and V-groove joint. Subsequently, toughness testing was carried out using the Charpy impact method. The steel material used in this study was ST 42. The results showed that holding time affected the toughness of PWHT-treated steel, where the lowest toughness value was 0.84 J/mm² at a holding time of 5 hours, and the highest toughness value was obtained at a holding time of 1 hour, with a toughness value of 1.366 J/mm². This proves that a longer holding time in the furnace leads to a decrease in the toughness of ST 42 steel subjected to PWHT at a temperature of 590°C.References
Ashby, M. F., & Jones,. (2012). Engineering Materials 1. Elsevier. https://doi.org/10.1016/C2009-0-64288-4
Bart, J. C. J., Gucciardi, E., & Cavallaro, S. (2013). Biolubricants: Science and technology. Woodhead publ.
Borgnakke, C., Sonntag, R. E., Van Wylen, G. J., & Sonntag, R. E. (2009). Fundamentals of thermodynamics (7th ed). Wiley.
Boumerzoug, Z., Derfouf, C., & Baudin, T. (2010). Effect of Welding on Microstructure and Mechanical Properties of an Industrial Low Carbon Steel. Engineering, 02(07), 502–506. https://doi.org/10.4236/eng.2010.27066
Fick, A. (1855). Ueber Diffusion. Annalen Der Physik, 170(1), 59–86. https://doi.org/10.1002/andp.18551700105
Haryadi, G. D., Ismail, R., & Haira, M. (2017). Pengaruh Post Weld Heat Treatment (Pwht) dengan Pemanas Induksi Terhadap Sifat Mekanik dan Struktur Mikro Sambungan Las Shield Metal Arc Welding (Smaw) pada Pipa API 5l X52. ROTASI, 19(3), 117. https://doi.org/10.14710/rotasi.19.3.117-124
Kavousi Sisi, A., & Mirsalehi, S. E. (2015). Effect of Post-Weld Heat Treatment on Microstructure and Mechanical Properties of X52 Linepipe HFIW Joints. Journal of Materials Engineering and Performance, 24(4), 1626–1633. https://doi.org/10.1007/s11665-015-1423-3
Márquez-Herrera, A., & Moreno-Palmerin, J. (2021). Corrosion resistance evaluation of boron-carbon coating on ASTM A-36 steel. Revista Mexicana de Física, 68(1 Jan-Feb). https://doi.org/10.31349/RevMexFis.68.011001
Nitha, N. (2019). Pengaruh Arus Pengelasan Terhadap Kekerasan, Kekuatan Tarik, Dan Struktur Mikro Hasil Las SMAW. Mechanical Engineering Science (MES) Journal, 1(2), 19–28.
Nitha, N., Sangkung, J., Fikran, F., Pasae, N., Bontong, Y., & Sampelawang, P. (2024). Korelasi Media Pendingin pada Pengelasan SMAW Terhadap Kekerasan Material ST 37 Post Preheating. Innovative: Journal Of Social Science Research, 4(6), 9466-9474.
Pratama, G. Y. (2022). Pengaruh Post Weld Heat Treatment (Pwht) Dengan Variasi Media Pendinginan Hasil Pengelasan SMAW Pada Pipa Kilang ASTM A 106 Grade B Terhadap Kekuatan Bending Dan Struktur Mikro. 10(03).
Putra Nugraha, Y. D., Suharno, S., & Estriyanto, Y. (2017). Pengaruh Proses Post Weld Heat Treatment (PWHT) Pada Pengelasan Material Paduan Super Berbasis Nikel Dengan Metode Tungsten Inert Gas (TIG) Terhadap Kekerasan Dan Struktur Mikro. Jurnal Ilmiah Pendidikan Teknik Dan Kejuruan, 10(2), 75. https://doi.org/10.20961/jiptek.v10i2.16916
Smallman, R. E., & Bishop, R. J. (1999). Modern Physical Metallurgy and Materials Engineering. Elsevier. https://doi.org/10.1016/B978-0-7506-4564-5.X5000-9
Nitha, Yafet Bontong, Petrus Sampelawang, Lantana Dioren Rumpa, Nofrianto Pasae, & Fikran. (2024). Pengaruh Temperatur Austenit dengan Holding Time 2 Jam Terhadap Kekerasan dan Ketangguhan Baja ST 42. JOURNAL OF ELECTRICAL AND SYSTEM CONTROL ENGINEERING, 7(2), 103–108. https://doi.org/10.31289/jesce.v7i2.11332
Nitha, N., Sampelawang, P., & Ba’dung, H. S. The Effectiveness of the Effect of Holding Time on the Toughness and Macro Structure of Low Carbon Steel Due to Carburizing Pack of Pine Charcoal. SITEKIN: Jurnal Sains, Teknologi dan Industri, 21(1), 84-87.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Nitha Nitha, Anis Tandiara, Fikran Fikran, Yafet Bontong, Nofrianto Pasae, Petrus Sampelawang
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
