Identifikasi Waste Defect Type 2 Dengan Pendekatan Metode Lean Manufacturing Untuk Meminimalisir Cacat Produksi pada ProsesTurning di CV. ABC

Authors

  • Nur Hamidah Universitas Nahdlatul Ulama Pasuruan
  • Enik Sulistyowati Universitas Nahdlatul Ulama Pasuruan
  • Iis Riyana Universitas Nahdlatul Ulama Pasuruan

DOI:

https://doi.org/10.31004/jutin.v8i3.48869

Keywords:

Lean Manufacturing, Value Stream Mapping, Waste defect , Turning, Fishbone Diagram

Abstract

CV. ABC is a wood-processing manufacturing company with one of its main products being turning components. The primary issue faced by the company is waste caused by frequent product defects due to human error. This study aims to minimize non-value-added activities and identify the root causes of human error in the turning production process. The Value Stream Mapping (VSM) method is used to map the process flow from raw materials to finished products. Data were collected through questionnaires and analyzed using WAM, WRM, and WAQ. The results identified the three highest types of waste: defect (27.979%), overproduction (15.471%), and inventory (12.363%). Waste prioritization was carried out using VALSAT, with PAM and QFM selected as the most influential tools. Fishbone analysis revealed lack of focus and attention to detail as the main causes of human error. Improvements were proposed through skill enhancement training, occupational health and safety (OHS) implementation, and regular checklist usage. As a result, processing time was reduced from 2,384.2 minutes to 2,247.4 minutes, as illustrated in the Future State VSM.

References

C. Kusbiantoro, “Penerapan Lean Manufacturing Untuk Mengidentifikasi Dan Menurunkan Waste ( Studi Kasus CV Tanara Textile ),” vol. 5, no. 1, pp. 1–7, 2019.

R. Prabowo, A. Suryanto, “Implementasi Lean dan Green Manufacturing Guna Meningkatkan Sustainability pada PT. Sekar Lima Pratama,“Jurnal SENOPATI,” pp. 50–61, 2019.

Y. Sinambela, “Penerapan Lean Manufakturing pada PT . XYZ,” vol. 6, no. 1, pp. 43–49, 2017.

Lukmandono, N. L. P. Hariastuti, Suparto, and D. I. Saputra, “Implementation of Waste Reduction at Operational Division with Lean Manufacturing Concept,” IOP Conf. Ser. Mater. Sci. Eng., vol. 462, no. 1, 2019.

A. A. Zahra, S. Indrawati, and J. Sulistio, “Performance Improvement in Aerospace Production Through Lean Manufacturing Implementation,” IOP Conf. Ser. Mater. Sci. Eng., vol. 722, no. 1, 2020.

R. Prabowo and R. Aditia, “Analisis Produktivitas Menggunakan Metode POSPAC dan Performance Prism Sebagai Upaya Peningkatan Kinerja (Studi Kasus: Industri Baja Tulangan di PT. X Surabaya),” J. Rekayasa Sist. Ind., vol. 9, no. 1, pp. 11–22, 2020.

A. Turseno, “Proses Eliminasi Waste Dengan Metode Waste Assessment Model & Process Activity Mapping Pada Dispensing,” J. Ind. Manuf., vol. 3, no. 1, pp. 45–50, 2018.

Y. U. Kasanah, P. P. Suryadhini, and M. Astuti, “Penerapan Lean Manufacturing Untuk Meminimasi Waste Delay Pada Workstation Curing di PT Bridgestone Tire Indonesia,” JATI UNIK J. Ilm. Tek. dan Manaj. Ind., vol. 2, no. 1, p. 14, 2019.

A. Ravizar and R. Rosihin, “Penerapan Lean Manufacturing untuk Mengurangi Waste pada Produksi Absorbent,” J. INTECH Tek. Ind. Univ. Serang Raya, vol. 4, no. 1, p. 23, 2018.

R. Prabowo, “Penerapan Konsep Line Balancing Untuk Mencapai Efisiensi Kerja Yang Optimal Pada Setiap Stasiun Kerja Pada PT. HM. Sampoerna Tbk,” J. IPTEK, vol. 20, no. 2, p. 9, 2016.

D. I. Pt, M. Dua, and T. Jember, “Metode Lean Manufacturing,” vol. 14, no. 02, pp. 51–59, 2019.

K. Arbelinda and R. Rumita, “Penerapan Lean Manufacturing pada Produksi Itc CV. Mansgroup dengan Menggunakan Value Stream Mapping dan 5s,” None, vol. 6, no. 1, pp. 1–10, 2017.

R. Prabowo, “Desain Penentuan Insentif Bagi Karyawan Untuk Meningkatkan Dual Mutualisme (Studi Kasus: PT. Arista Assembling and Packing Surabaya),“Jurnal TECNOSCIENZA,vol. 2, no. 2 pp. 83–106, 2018.

Suharjo and S. Sudiro, “Pengurangan Pemborosan Pada Proses Produksi Dengan Menggunakan WRM, WAQ dan Valsat Pada Sistem Lean Manufaktur (Studi Kasus Pada Produksi Setrika Lisrik),” Teknobiz J. Ilm. Progr. Stud. Magister Tek. Mesin, vol. 8, no. 2, pp. 61–68, 2018.

Downloads

Published

2025-07-15

How to Cite

Hamidah, N., Sulistyowati, E., & Riyana, I. (2025). Identifikasi Waste Defect Type 2 Dengan Pendekatan Metode Lean Manufacturing Untuk Meminimalisir Cacat Produksi pada ProsesTurning di CV. ABC. Jurnal Teknik Industri Terintegrasi (JUTIN), 8(3), 3590–3598. https://doi.org/10.31004/jutin.v8i3.48869

Issue

Vol. 8 No. 3 (2025): July

Section

Articles of Research

License

Copyright (c) 2025 Nur Hamidah, Enik Sulistyowati, Iis Riyana

Creative Commons License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Similar Articles

1 2 3 4 5 6 7 8 9 10 > >> 

You may also start an advanced similarity search for this article.

Most read articles by the same author(s)

<< < 1 2 3 > >>