Analisis Penyebab Produk Defect Jenis Dust di Proses Visual Inspection Menggunakan Metode Failure Mode and Effect Analysis (FMEA)

Ayu Putri Purwani; Eva  Safariyani; Muhammad Primasuri  Anbiya

doi:10.31004/jutin.v7i3.27694

Authors

Ayu Putri Purwani Fakultas Teknik, Program Studi teknik Industri, Universitas Singaperbangsa Karawang
Eva Safariyani Fakultas Teknik, Program Studi teknik Industri, Universitas Singaperbangsa Karawang
Muhammad Primasuri Anbiya Fakultas Teknik, Program Studi teknik Elektro, Universitas Singaperbangsa Karawang

DOI:

https://doi.org/10.31004/jutin.v7i3.27694

Keywords:

Quality Control, Process Production, FMEA, Visual Inspection

Abstract

PT XYZ is a manufacturing company that produces electronics. During the production process, a significant issue has been identified - a high number of defective products due to dust contamination. This research is designed to analyze the factors contributing to these defects during the visual inspection process, using the Failure Mode and Effect Analysis (FMEA) method. This research can identify the factors causing failure, the severity level, and the probability of negative effects of the failure. Additionally, it allows us to determine the corrective actions or improvements needed to prevent or reduce the risk of product failure during the visual inspection process. The results of the research indicate that the primary cause of the NG dust-type products, based on the highest Risk Priority Number (RPN) value of 320, is operator skills. This factor is a potential cause of the NG dust-type products. Therefore, analysis and simulation of proposed improvements are being conducted, to reduce the number of NG products in the visual inspection process.

References

Anastasya, A., & Yuamita, F. (2022). Pengendalian Kualitas Pada Produksi Air Minum Dalam Kemasan Botol 330 ml Menggunakan Metode Failure Mode Effect Analysis (FMEA) di PDAM Tirta Sembada. Jurnal Teknologi Dan Manajemen Industri Terapan, 1(I), 15–21. https://doi.org/10.55826/tmit.v1ii.4

Andiana, R., Adhitya, R., Amri, A. M., & Perkapalan Negeri Surabaya, P. (2022). Penerapan Metode LSB Untuk Perbaikan Kualitas Citra Pada Proses Inspeksi Visual Pengelasan. 1(2), 151–156. http://melatijournal.com/index.php/Metta

Andriyanto, A., & Ega Anggraini Putri, Y. (2021). Analisis Penyebab Kegagalan Pengiriman Barang Project 247 Atau Jenis Sxq Pada Divisi Operation Airfreight Pt.Cipta Krida Bahari Dengan Metode Failure Mode and Effect Analysis (Fmea) Dan Fault Tree Analysis (Fta). Jurnal Logistik Bisnis, 11(1), 7–13. https://doi.org/10.46369/logistik.v11i1.1372

Fernandi, M. R., Risqi, A. W., & Negoro, Y. P. (2022). Analisis Kualitas Produk Minyak Goreng Kemasan Standing Pouch Menggunakan Metode FMEA pada PT. KIAS. Serambi Engineering, VII(3), 3646–3657.

Herasmus, H., Amrina, E., & Sanusi, S. (2021). Peningkatan Efisiensi Kerja Dengan Menggunakan Jig Inspeksi Dengan Metode Pdca Di Proses Visual Inspection Di Pt Xyz. PROFISIENSI: Jurnal Program Studi Teknik Industri, 9(1), 117–123. https://doi.org/10.33373/profis.v9i1.3335

Khatammi, A., & Wasiur, A. R. (2022). Analisis Kecacatan Produk Pada Hasil Pengelasan Dengan Menggunakan Metode FMEA (Failure Mode Effect Analysis). Jurnal Serambi Engineering, 7(2), 2922–2928. https://doi.org/10.32672/jse.v7i2.3853

Krisnaningsih, E., Gautama, P., & Syams, M. F. K. (2021). Usulan Perbaikan Kualitas Dengan Menggunakan Metode Fta Dan Fmea. Jurnal InTent, 4(1), 41–54.

Mulyana, I. J., Hartoyo, S. S., & Sianto, M. E. (2022). Defect Analysis of Printing Process in Offset Printing Industry by Using Failure Mode Effect Analysis (FMEA) and Fault Tree Analysis (FTA). Journal of Integrated System, 5(2), 143–155. https://doi.org/10.28932/jis.v5i2.5241

Pandey, M., Tirayoh, V. Z., Maradesa, D., Akuntansi, J., Ekonomi, F., Ratulangi, U. S., & Bahu, K. (2024). Penerapan Metode Activity Based Management dalam Meningkatkan Efisiensi Aktivitas dan Biaya Produksi pada PT Sinar Pure Foods International Bitung Application Of Activity Based Management Method In Improving The International Bitung. 8(1), 50–59.

Putri, A. S. (2023). REWORK DENGAN METODE FMEA PADA INTIMATES WEAR PRODUCT. 4(1), 15–23.

Rahman, A., & Perdana, S. (2021). Analisis Perbaikan Kualitas Produk Carton Box di PT XYZ Dengan Metode DMAIC dan FMEA. Jurnal Optimasi Teknik Industri (JOTI), 3(1), 33–37. https://doi.org/10.30998/joti.v3i1.9287

Saepudin, T. H., & Laksono, R. F. (2023). Upaya Penurunan Produk Cacat Pada Proses Painting Unit CN113R Dengan Metode Failure Mode Effect Analysis ( FMEA ). 2(Mei), 15–21.

Wicaksono, A., Dhartikasari Priyana, E., & Pandu Nugroho, Y. (2023). Analisis Pengendalian Kualitas Menggunakan Metode Failure Mode and Effects Analysis (FMEA) Pada Pompa Sentrifugal Di PT. X. Jurnal Teknik Industri: Jurnal Hasil Penelitian Dan Karya Ilmiah Dalam Bidang Teknik Industri, 9(1), 177. https://doi.org/10.24014/jti.v9i1.22233

Zendrato, R. V., Ryantama, R., Nugroho, M. A., Putri, D., Kuncoro, D., & Parningotan, S. (2022). Analisis Pengendalian Kualitas Pada Tempe Menggunakan Metode Seven Tools. IMTechno: Journal of Industrial Management and Technology, 3(2), 99–109. https://doi.org/10.31294/imtechno.v3i2.1221